Search a Product
 
 
Home> Support> Installation> LUX 800
>> click here for detail image
 
IMPORTANT: Read instructions completely before starting installation.

We recommend that the instructions and diagrams be printed for easy reference during installation.
Before starting installation, check that all FreshWash components are available, that the unit fits the toilet to which it will be added, and that the water shutoff valves to be used are working properly.

FreshWash LUX models require access to a 10 Amp grounded GFCI outlet, located on the wall within reach of the unit's power cord (give cord length). The outlet is available, do not install until the outlet is replaced with a properly-safe 3 prong version.


INSTALLATION SAFETY WARNINGS
  • Electrical cord must be at least 2.0M long.
    •
  • If installing an electrical socket, ensure that is at least 30cm above the floor.
    •
  • Wires must be grounded to prevent electrical shocks. Connect ground wire to metal water pipe or the fixing support of the basin.
    •
  • Do not ground to a gas pipe or a lightning rod of telephone wire, as these may conduct lightning to the product.
    •
  • Install only in well-ventilated areas to avoid excess humidity. Do not install in narrow toilet stall or in shower stalls.
    •
  • Install only where direct contact with water is minimized.
    •
  • Do not install near any heat source.
    •
  • Avoid using extension cords if possible. Use only to prevent leakage wherever bolt and nut are applied where extension cords are necessary.
Step 1: Removing the existing toilet seat and lid.
    Unfasten the nuts and remove toilet seat and lid.
Step 2: Installing the FreshWash water connection. (Diagram 1)
   
  • Turn off the toilet's water shutoff valve on the water supply pipe.
    •
  • Drain the toilet tank by flushing the toilet normally.
    •
  • Place a pan or bowl beneath the shutoff valve and the pipe connecting the water supply to the toilet tank to catch any water left in pipes when unfastening the coupling nut on the pipe. Unfasten the connecting pipe by unscrewing the coupling nuts. Be careful not to damage the pipe.
  • If the connecting pipe is not flexible, replace it with the flexible pipe provided.
    •
  • Insert the rubber wash into the T-joint to prevent leaks and attach the T-joint to the water supply pipe after placing the TEFLON tape on the thread fo the pipe, firmly tightening the coupling nut.
  • Attach one end of the flwxible pipe-B to the top of the T-joint and the other end to the water intake of the toilet water tank. Tighten firmly by hand. Do not use tools as they may damage the flexible pipe-B.
  • Close the remaining T-joint connection and open the water shutoff valve to check for leaks. If the T-joint leaks, check that the rubber washer is seated properly and gently tighten the valve connector with a plastic wrench.
    •  
    Step 3: Placing the main unit on the toilet. (Diagram 2)
       
  • Measure the distance between two mounting holes of the toilet bowl. Insert the bolts proviced into the holes at the base of the FreshWash seat at the appropriate distance.
  • Place the rubber pads around the bolt holes on the toilet, and lift the FreshWash unit onto the toilet.
  • Lift seat and cover and insert the bolts into the proper holes on the toilet as shown in diagram 2. Place a nut on each bolt and tighten with plastic tools to hold the FreshWash unit firmly in place. Apply gentle pressure only to avoid damage.
    		•
    Step 4: Hooking up the water supply for the main unit.
    (Diagram 1A,1B)
       
  • Connect the metal end of the flexible pipe-A to the remaining T-joint, connect the platic end of the flexible pipe, and the other to the FreshWash unit.
  • (With the water filter) As shown in the diagram 1B, insert the provided rubber washer into the water filter and connect the water filter to the tap water connection. Tighten firmly by hand.
    		•
    Step 5: Grounding the unit.
        The LUX unit must be grounded to operate safely. Attach the green ground wire to the ground terminal or the metal pipe. DO NOT attach to a plastic pipe, as this will not ground the unit. DO NOT attach to a gas pipe, telephone wire, or lightning rod, as these may conduct lightning charges to the unit.
    Step 6: Checking that the unit is functioning properly.
       
  • Open the water shutoff valve slowly to check that there are no leaks. If there are leaks, turn off the water supply at the valve and tighten connections. Teflon tape is strongly recommended to be applied at all connections to prevent leakage.
  • Check that the unit is seated firmly on the toilet and that water is running into the warm water tank.
    •
  • Plug in the power cord and check that the unit is functioning properly. Apply weight to the seat to activate the nozzles placing a cup or your hand over the nozzles to prevent water splattering. Spraying will cease automatically after 40-60 seconds.
    •
  • Save the toilet seat, cover, and pipe removed in installation so that the toilet may be restored to its original condition if desired.
    		•
    You are now ready to use your FreshWash LUX unit according to the directions.
    > click here for how to use LUX 800
     
     

     

     

     

     

     
    One Militia Drive, Lexington, MA 02421  l  Call Toll Free 1.800.960.4960  l  info@myFreshWash.com
    Copyright © 2004, Healthy Life Corporation. All Rights Reserved.